HPDM (High Power Density Modules)

Available at D, DH-series Modules, designed for applications requiring high-performance modules where are needed to reject large amount of heat (lasers, CPU-coolers, test systems).

Alumina and aluminum nitride, ceramic metallization, pre-tinning are available.

S, SN, R, C, CH, D, DH, H – TYPICAL PRODUCT SERIES AVAILABLE

“D” - SERIES, HIGH POWER DENSITY MODULES (“HPDM”)

Modules, designed for applications requiring high performance modules where the devices (lasers, thermal stabilization of test bench device for chip production, etc.) produce a large amount of heat that needs to be removed constantly or in a short time.

•• Maximum temperature for short time (to mount a module into unit): 130°С

•• Recommended operating temperature: up to 120°С

•• Recommended operation current: 0.5 – 0.7 of Imax.

•• Minimal cycling stability in ON-OFF power mode: over 60 000 cycles (cycle time is 60/60 seconds)

•• Minimal cycling stability in 20/80°С power cycling mode: up to 25 000 cycles

•• Recommended operating temperature not higher than 90°С

•• At operating current (I) close to 0,5 from Imax these modules provide COP, close to 1.

“DH” - SERIES, HIGH POWER DENSITY MODULES, “HPDM + HOT"

Thermoelectric modules, designed for applications requiring high performance modules where the devices (lasers, thermal stabilization of test bench device for chip production, etc.) produce a large amount of heat per square.

•• Maximum temperature for short time (to mount a module into unit): 200°С

•• Maximum operation temperature: 150°С

•• Recommended operation current: 0.5 – 0.7 of Imax.

•• Minimal cycling stability in ON-OFF power cycling mode: over 60 000 cycles (cycle time is 60/60 seconds)

•• Minimal cycling stability in 20/80°С power cycling mode: over 25 000 cycles

OPTIONS FOR SURFACES FINISH:

L1 – height tolerance ± 0.01mm

L2 – height tolerance ± 0.02mm

R – round shape of the module

H – module has a circular hole in the ceramics

Mch – both sides have metallization (height tolerance ±0.15)

Mc – only cold side has metallization (height tolerance ±0.15)

Mh – only hot side has metallization (height tolerance ±0.15)

TchX – both sides have tinning, height tolerance before tinning ±0.15

TcX – only cold side has tinning, height tolerance before tinning ±0.15

ThX – only hot side has tinning, height tolerance before tinning ±0.15

X – type of solder used for tinning: 1 – solder with melting temperature 117°С ,

2 – solder with melting temperature 138°С.

No code – module is not lapped, without metallization or tinning

SEALING TYPE

S – silicon sealing;

E – epoxy sealing;

Absence of sealing index means modules without sealing.

NOTE! MAX ΔT IS REDUCED BY 2-3°С FOR SILICONE AND BY 1-2°С FOR EPOXY SEALING VERSIONS.

THE MODULES CAN BE ASSEMBLED IN KITS WITH SERIES OR PARALLEL CONNECTION OR INSTALLED IN A DEVICE FOLLOWING CUSTOMER’S DESIGN & CONSTRUCTION DOCUMENTATION

Terms and Definitions

Catalog Number

Type

↑ ↓

Series

↑ ↓

Thot=25°C

R, Ohm
at 25°C, AC

↑ ↓

Dimensions

Imax, А
↑ ↓

Umax, V
↑ ↓

Qmax, W
↑ ↓

△Tmax, K
↑ ↓

Length А/А1, mm
↑ ↓

Witdh В, mm
↑ ↓

Height Н, mm
↑ ↓

D-128-10-05
datasheet

HPDM

DH, D

9.2

16.3

91.6

68.0

1.37

30/34

2.80

D-241-10-05
datasheet

HPDM

DH, D

9.2

30.7

172.5

68.0

2.59

40/44

2.80

D-288-10-05
datasheet

HPDM

DH, D

9.2

36.7

206.2

68.0

3.09

40/44

2.80

D-199-10-06
datasheet

HPDM

DH, D

7.7

25.3

120.9

2.51

3.10

D-288-10-08
datasheet

HPDM

DH, D

5.8

36.7

131

71.0

4.84

40/44

3.10

D-032-14-045-Mch
datasheet

HPDM

21.5

4.1

53.4

0.15

20/24

3.30

D-128-14-045
datasheet

HPDM

21.5

16.3

213.6

0.59

40/44

3.10

D-128-14-06
datasheet

HPDM

DH, D

15.1

16.2

151.2

0.82

40/44

3.30

D-200-14-06
datasheet

HPDM

DH, D

15.1

25.5

238.2

1.29

40/44

3.30

D-242-14-06
datasheet

HPDM

DH, D

15.1

30.7

287

1.55

52/56

3.30

D-288-14-06
datasheet

HPDM

DH, D

15.1

36.7

342.9

1.85

52/56

3.30

D-200-14-11
datasheet

HPDM

DH, D

7.9

25.5

124.8

72.5

2.45

40/44

3.80

D-288-14-11
datasheet

HPDM

DH, D

7.9

36.7

179.7

72.5

3.52

52/56

3.80

D-128-20-08
datasheet

HPDM

DH, D

22.6

16.3

227.9

71.0

0.55

55/59

4.00