S, SN, R, C, CH, D, DH, H – TYPICAL PRODUCT SERIES AVAILABLE
“S” - SERIES, “STANDARD”
High performance thermoelectric modules for traditional cooling applications (refrigeration, electronics, industrial, automotive)
•• Maximum temperature for short time (to mount a module into unit): 130°С
•• Recommended operation temperature: up to 120°С
•• Max ΔT up to 75°С (at Thot=25°С)
•• Minimal cycling stability in ON-OFF power cycling mode: over 60 000 cycles (cycle time is 60/60 seconds)
•• Recommended operation current: 0.7 of Imax
•• Recommended operation voltage: 0.8 of Umax
•• Wires: UL-1569 in PVC insulation
“R” - SERIES, “RELIANCE”
High performance for traditional cooling applications (refrigeration, electronics, industrial, automotive)
•• Maximum temperature for short time (to mount a module into unit): 120°С
•• Recommended operating temperature: up to 90°С
•• Max ΔT: up to 75°С (at Thot= 25°С)
•• Minimal cycling stability in ON-OFF power cycling mode: over 60 000 cycles (cycle time is 60/60 seconds)
•• Minimal cycling stability in 20/80°С power cycling mode: over 25 000 cycles
•• Recommended operation current: 0.7 of Imax
•• Recommended operation voltage: 0.8 of Umax
•• Wires: UL-1569 in PVC insulation
“C” - SERIES, “CYCLE”
Thermoelectric modules, designed for applications that imply long-term cycling stability with the change of polarity of electric current (lasers, thermal stabilization device test stands chip production, etc.).
•• Maximum temperature for short time (to mount a module into unit): 130°С
•• Recommended operating temperature: up to 120°С
•• Recommended operation current: 0.7 of Imax.
•• Max ΔT: up to 75K (at Thot= 25°С)
•• Minimal cycling stability in ON-OFF power cycling mode: over 60 000 cycles (cycle time is 60/60 seconds)
•• Minimal cycling stability in 20/80°С power cycling mode: up to 25 000 cycles
“H” – SERIES, “HOT”
Thermoelectric modules, designed for applications requiring high efficiency unit at operating temperature, not exceeding 150°C. Possible to use in the long-term heating mode.
•• Maximum temperature for short time (to mount a module into unit): 200°С
•• Recommended operation temperature: up to 150°С
•• Max ΔT up to 75K (at Thot=25°С)
•• Minimal cycling stability in ON-OFF power cycling mode: over 60 000 cycles (cycle time is 60/60 seconds)
•• Modules of this series pass additional annealing at 150°С
•• Recommended operation current: 0.7 of Imax
OPTIONS FOR SURFACES FINISH:
L1 – height tolerance ± 0.01mm
L2 – height tolerance ± 0.02mm
R – round shape of the module
H – module has a circular hole in the ceramics
Mch – both sides have metallization (height tolerance ±0.15)
Mc – only cold side has metallization (height tolerance ±0.15)
Mh – only hot side has metallization (height tolerance ±0.15)
TchX – both sides have tinning, height tolerance before tinning ±0.15
TcX – only cold side has tinning, height tolerance before tinning ±0.15
ThX – only hot side has tinning, height tolerance before tinning ±0.15
X – type of solder used for tinning: 1 – solder with melting temperature 117°С ,
2 – solder with melting temperature 138°С.
No code – module is not lapped, without metallization or tinning
Absence of sealing index means modules without sealing.
NOTE! MAX ΔT IS REDUCED BY 2-3°С FOR SILICONE AND BY 1-2°С FOR EPOXY SEALING VERSIONS.
THE MODULES CAN BE ASSEMBLED IN KITS WITH SERIES OR PARALLEL CONNECTION OR INSTALLED IN A DEVICE FOLLOWING CUSTOMER’S DESIGN & CONSTRUCTION DOCUMENTATION
